Plan a new or replacement forced-air heating system around the home's heating requirements, existing ductwork, and mechanical configuration.
Coquitlam Homes
Coquitlam has a mix of older detached homes, newer subdivisions, multi-level houses, townhomes, and renovated properties. From Burke Mountain and Westwood Plateau — where newer multi-level construction is common — to Maillardville, Ranch Park, and Central Coquitlam with their established older housing stock, the right furnace and installation scope varies from one home to the next. Floor-to-floor heating comfort, existing ductwork configuration, and mechanical space layout all factor into the planning conversation.
Whether you're replacing an aging unit or installing in a new space, the starting point is a proper assessment of your home's heating requirements — not the old equipment's nameplate rating.
Multi-level homes in Burke Mountain and Westwood Plateau often have uneven heating — upper floors that run too warm, lower floors that don't reach temperature. Proper duct balance, equipment sizing, and zoning are addressed through the assessment.
Many Coquitlam homes have existing forced-air duct systems. A new furnace is selected to work with the existing layout where it's suitable — and modifications are identified where they're needed for proper airflow and balance.
Newer homes in Westwood Plateau and Burke Mountain typically have modern duct systems and equipment sized for open-plan layouts. Replacement projects in these homes often have more straightforward scope — but still require assessment before equipment is specified.
Homes in Maillardville and Central Coquitlam often have older duct systems, tighter mechanical rooms, or original venting that may need updating to meet current standards or support a higher-efficiency furnace.
Furnace installation involves gas connection, venting, combustion air, and electrical. Exact scope depends on the equipment selected and the existing configuration — this is assessed before any equipment is ordered, not after.
Strata properties may have restrictions on venting penetrations and mechanical modifications. Where strata rules apply, we factor them into the project scope before finalizing the equipment selection.
What's Involved
A complete furnace installation project covers assessment, equipment selection, all connected trades work, commissioning, and homeowner handover.
We assess the home's heating load, existing ductwork condition and airflow balance, mechanical room, gas supply, current venting, and electrical. This drives equipment selection and project scope — not a guess from square footage.
Furnace capacity (BTU output) and efficiency (AFUE) are matched to the home's requirements. A higher AFUE rating reduces operating costs but affects venting requirements. We present options and explain the tradeoffs.
Existing ducts are reviewed for condition, sizing, and balance. Where modifications are needed — added returns, resized runs, or sealed leaks — these are included in the project scope, not discovered after installation.
Gas line sizing, venting type (single or two-pipe), combustion air, and electrical connections are all project-specific. The scope matches what the equipment requires and what the home's configuration demands.
The system is started up, verified, and tested — checking heat output, airflow balance, safety controls, and thermostat operation. We don't hand over a system that hasn't been confirmed working correctly.
We walk you through basic operation: thermostat settings, filter location and replacement schedule, what to expect from the system, and what to call about if something seems off.
Gas work requires licensed technicians. Furnace installation involves regulated gas connections, venting, and safety controls. Homeowners should not attempt to modify gas piping, bypass safeties, adjust combustion settings, or alter venting — these tasks require certified gas technicians and proper equipment.
How It Works
From first call to a commissioned, working system — how a Coquitlam furnace installation comes together.
We look at the heating load, existing ductwork, mechanical room, gas supply, venting, and electrical. The goal is understanding the full picture before recommending anything.
Equipment is selected based on the load calculation and the home's requirements — capacity, efficiency, and fuel type. Options are presented with clear tradeoffs.
The full installation scope is defined — equipment, gas, venting, electrical, ductwork (if any), and controls — and a clear quote is provided before any work is authorized.
Installation is completed by certified technicians. Gas connections, venting, combustion air, and electrical scope are all handled correctly. No shortcuts on the installation itself.
The system is commissioned and verified operating correctly. Heat output, safety controls, and airflow balance are checked before we leave. You're walked through everything you need to know about the new system.
Comparing Options
If you're making a replacement decision, it's worth understanding both paths before committing to either.
| Factor | Gas Furnace | Heat Pump |
|---|---|---|
| Heating | Yes — gas combustion | Yes — extracts heat from outdoor air |
| Cooling | No — separate AC required | Yes — heating and cooling in one system |
| Fuel | Natural gas | Electricity |
| Rebate eligibility | Generally not eligible for heat pump rebates | May qualify for CleanBC and BC Hydro rebates |
| Best fit | Replacing an existing gas furnace, keeping gas heat | Reducing fossil fuel use, or replacing heating + adding cooling |
Project Cost
We don't publish city-specific price ranges — project cost depends on your specific home, equipment selection, and installation scope.
For a full breakdown of what drives furnace installation pricing across Metro Vancouver — including equipment efficiency, venting, gas scope, ductwork, and access — see our Furnace Cost Vancouver guide. The same scope factors apply to Coquitlam projects.
Common Questions
We assess your home, explain your options, and provide a clear quote before any work begins.
Request ServiceCall us: (250) 201-2030